Microtronik Autohex II BMW WVCI HW4 Diagnostic Scan Coding Programming Tool Full Package

Autohex II HW4 and full functions available in BMW from ISN read write to key programming and BMW Ecu programming and coding (HexTag is included)

Using this kit you can do following:

• Read old ISN in BMW E series for following Ecus:D62M57A0,  D62M57B0,  D60PSA0,  D50M57A0,  D50M57E1,  D60M47A0,  D60M57A0,  MEV9N46L,  ME9N45,  ME9N62,  ME9E65_6,  N73_L0,  N73_R0,  ME9N62_2,  MSV70,  MS450DS0,  N62_TUE,  N62_TUE2.
• Read Long ISN (SK) in BMW E series from following Ecus:  MSV80,  MSD80,  MSD81,  MSD85,  MSD85Y,  MSS60,  MEVD176K,  ME17N45,  MED17_2,  MED17_2N,  MEV17_2,  MEV17N46,  MEVD174K, MEVD174KW,  MV1722,  MVD1722,  MEVD172,  MEVD1724,  MEVD1725,  MEVD172Y,  MEVD17KW,  D70N47A0,  D70N47B0,  D71N47A0,  D71N47B0,  D71N47C0,  D71N47D0,  D72N47A0,  D72N47B0,  D73N47A0,  D73N57A0,  D73N57B0,  D73N57C0,  D73N57D0
• Read Long ISN (SK) in BMW F series from following Ecus: MEVD172Y,  MEVD172,  MEVD1724,  MEVD1725,  N63TU_L0,  N63TU_R0,  S63TU_L0,  S63TU_R0
• Read/Write long ISN (SK) in BMW E and F series on Bench using Factory Mode. No need to open the DME/DDE (Only Autohex II can do this function)
• ISN Reading from Tricore Ecus by boot mode.
• Indivedual Programming for any Ecu in BMW E and F series
• Ecu Swapping if hardware is matched.
• CAS1, CAS2, CAS3 and CAS3+ read and write ISN and SK
• Key Programming For E and F series (CAS1, CAS2, CAS3, CAS3+, CAS4 ,CAS4+, FEM, BDC)
• BMW E series EGS ISN matching with CAS
• BMW F series EGS 6HP and 8HP EWS Resetting
• BMW E Series, F Series and G Series coding for all Ecus (calculation of Ecucoding is calculated from FA)
• BMW advanced coding (manual coding)
• Vehicle order modification and backup and restore from LM,FRM,...ETC
• Do diagnose and service functions from Autohex II (Read and erase fault codes, data stream values, activations, reset adaptation,...)
• Use BMW ISTA-D on Autohex II WVCI (BMW ISTA-D Driver)
• Unlock secrity of BDC and FEM to able to: Change BDC and FEM VIN, Change BDC and FEM ISN, Mileage Reset for BDC and FEM, and making a key for BDC and FEM.
• Read and write ISN of MSD85, MSD87, MSV90 in F series.
• Ecu Cloning/Tuning for a wide range of brands. This function is free for 30 days (Check Supported Ecu List).
• Read and write CAS 1,2,3,4 EEPROM and FLASH 100% safely using HexTag tool.
• Read and write other modules from BMW,Mercedes, Audi, and others BDM protocol by HexTag tool
• Modify KOMBI Mileage by HexTag tool
• Renew all BMW keys, and many other brands by HexTag tool.

What you get:

• Autohex II Hardware WVCI HW 4
• HexPROG Key programmer
• BMW Software Standard License
• ISN Boot Mode License
• BMW Ecu Programming License
• BMW Key Programming License
• BMW ISTA/D driver to run dealer software
• 1 year technical support
• 1 year hardware warranty
• 1 year online access to online programming